Plumbing & HVAC in Florissant, MO

Completed routine furnace tune-up on basement-located air handler unit. Performed comprehensive system inspection including visual assessment of ductwork connections, condensate drain lines, and electrical components. Filter inspected and found in acceptable condition with minimal debris accumulation. All mechanical connections, including galvanized supply ductwork and refrigerant lines, verified secure and properly sealed. System operational and functioning within normal parameters upon completion of maintenance service.

Completed comprehensive furnace tune-up on U10 unit located in basement. Performed standard maintenance procedures including filter inspection, thermostat functionality verification, and system diagnostics. Unit operating within normal parameters with thermostat displaying proper temperature readings and all controls functioning correctly.

Responded to return service call to locate missing disconnect component from previous repair visit. Searched shed roof above outdoor air conditioning unit as indicated by service notes. Unable to locate original disconnect stab. Proceeded to install new electrical disconnect at outdoor unit. Verified proper electrical connections, tested system operation, and confirmed unit returned to normal heating and cooling function.

Responded to recall for non-cooling AC unit at residential property with 10-year-old outdoor condenser located at side of home. Upon inspection, found outdoor electrical disconnect box with severe deterioration, corrosion on terminal connections, accumulated debris, and evidence of moisture intrusion affecting wire nut connections and terminal blocks. Addressed electrical safety concerns and restored proper system operation.

Completed installation of a 50-gallon tall gas water heater in a walkout basement utility area. Connected copper supply lines, PVC venting, and gas piping to manufacturer specifications, ensuring proper clearances and secure mounting. Applied required identification sticker and obtained permit compliance for final inspection.

Responded to no cooling call with unit freezing up. Found severely restricted airflow due to heavily clogged air filter saturated with dust and debris. Replaced dirty filter with new filter, restored proper airflow to system, and verified unit operating normally without freezing.

Completed annual preventative maintenance tune-up on outdoor condensing unit located in side yard. Performed comprehensive system inspection including electrical connections, dual-run capacitor testing (19/40 MFD), refrigerant line inspection, and verification of all safety controls. Inspected 16x25x1 air filter and confirmed proper installation, checked all wiring connections and copper refrigerant tubing for integrity, and verified unit operational status with system operating as designed.

Conducted on-site electrical assessment for Kohler generator installation. Evaluated existing main electrical panel to determine compatibility and available capacity for generator integration. Panel inspection revealed fully utilized breaker spaces with handwritten circuit identification labels for main service, HVAC, kitchen appliances, garage circuits, and various room designations. Documented current electrical infrastructure including main breaker configuration, existing circuit distribution, and panel specifications to develop comprehensive installation estimate. Assessment included verification of service entrance capacity, evaluation of transfer switch placement requirements, and determination of necessary electrical modifications to accommodate automatic standby generator system.

# HVAC Furnace Tune-Up - Home Depot Service Performed comprehensive tune-up and inspection on residential forced-air furnace system located in garage utility room. Conducted thorough examination of all major components including blower motor assembly, gas valve with multi-wire connections, burner assembly, and heat exchanger sections. Inspected electrical connections throughout the unit, verifying proper wiring integrity on all circuits. Evaluated burner operation and combustion chamber condition. Assessed overall system functionality and verified safe operation of all heating components. Documented equipment condition through photographic records showing internal cabinet components and external unit housing with ventilation grilles. Noted minor dust accumulation in lower cabinet area typical of operational systems. All safety labels and manufacturer warnings confirmed present and legible. Unit operational and performing within normal parameters upon completion of tune-up service.

Completed comprehensive tune-up service on single residential air conditioning unit located on side of home. Performed standard maintenance protocol including system inspection, replaced 20x25x1 pleated air filter, verified proper operation of furnace and ductwork components, and documented equipment condition through photographic records. All systems tested and confirmed operational upon completion.

Completed comprehensive AC Super Tune service on Ruud residential HVAC system with age unknown to homeowner. Performed full system inspection including furnace, evaporator coil, and control board components. Verified all electrical connections, refrigerant line integrity, gas piping, and shut-off valves functioning properly. Inspected control board wiring and terminals, confirmed proper operation of all safety controls and system components. System operating within normal parameters with no deficiencies noted at time of service.

Completed comprehensive Supertune maintenance service on a 10-year-old combination AC and heat pump furnace system located at ground level in the rear of the property. Performed full system inspection with furnace cabinet opened to access and evaluate internal components including blower motor assembly, electrical connections, and mechanical operations. Conducted standard tune-up procedures on both heating and cooling systems to ensure optimal performance and efficiency for the upcoming season.

Responded to residential service call to repair or replace two receptacles and switches. Upon arrival, performed visual inspection of electrical system including exterior meter base, service entrance equipment, and associated wiring connections. Documented existing conditions with photographs showing digital utility meter, exterior junction boxes, and service conduit installation. Accessed interior locations to evaluate and service the affected receptacles and switches as requested. Completed necessary repairs or replacements to restore proper functionality to the electrical devices. Verified all connections were secure and tested circuits to ensure safe operation. All work performed in accordance with National Electrical Code standards.

Responded to no cooling complaint on Lennox system following power outage from transformer failure. Upon arrival, found unit running but house temperature at 85°F. Diagnosed issue as thermostat programming lost during power interruption on recently installed digital thermostat. Reprogrammed thermostat to proper cooling setpoints and verified system operation. Used clamp meter to verify amperage draw on compressor and confirmed readings within manufacturer specifications. Connected manifold gauges to measure refrigerant pressures and temperatures, confirming system charging and performance parameters were correct at 142.3 PSI high side and 117 PSI low side with superheat at acceptable levels. Instructed occupant on proper thermostat operation and programming procedures to prevent future issues. System cooling properly upon departure with all components operating as designed.

# HVAC Tune-Up Completed Performed comprehensive preventative maintenance tune-up on a single outdoor air conditioning condenser unit located in backyard. Conducted standard inspection protocol including visual assessment of unit exterior, electrical disconnect box, conduit connections, and mounting hardware. Verified proper clearance around unit despite vegetation growth near base and wall-mounted components. Inspected indoor air handler system with focus on filter specifications and operational safety labels. All routine maintenance tasks completed per manufacturer guidelines for optimal system performance and seasonal readiness.

Completed electrical estimate for sub panel installation at residential property. Evaluated existing main electrical panel, which contains two columns of circuit breakers serving various household circuits including HVAC, water heater, kitchen appliances, bedrooms, and living areas. Observed dense wiring configuration with multiple wire runs and connections throughout the existing panel enclosure. Assessed current electrical load distribution and available capacity to determine specifications and requirements for proposed sub panel installation. Documented existing panel condition and circuit layout to develop accurate scope of work and material requirements for the sub panel project.

Responded to no cooling complaint on 8-year-old Lennox central air conditioning system with attic-mounted air handler. Upon arrival, discovered condensate drain line completely blocked, causing secondary drain pan to overflow and trip safety float switch, which shut down the system. Cleared obstruction from primary drain line, flushed condensate system with approved cleaning solution, and verified proper drainage flow. Tested float switch operation and confirmed system restored to normal cooling operation with proper airflow and temperature differential across evaporator coil.

Responded to clogged bathroom sink caused by deteriorated P-trap assembly with visible corrosion at metal coupling and compromised pipe integrity. Removed failed trap section showing extensive mineral buildup and coating degradation, installed new P-trap assembly with proper sealing, and verified drainage flow restoration. Cleared standing water and confirmed all connections leak-free upon completion.

Responded to water leak complaint on residential furnace system located in basement. Upon arrival, performed visual inspection of HVAC unit less than 10 years old. Identified water leakage originating from furnace area. Inspected Aprilaire humidifier component and associated copper piping connections for potential leak sources. Examined air handler unit, condensate drainage system, and surrounding ductwork for moisture accumulation. Documented system conditions with photographic evidence showing air filter assembly, humidifier installation, and copper refrigerant lines. Unable to complete full diagnostic assessment and repair at time of visit. System requires follow-up service to isolate leak source and implement necessary repairs to resolve water discharge issue.

Responded to loss of power affecting main level circuits. Upon inspection, found electrical panel with debris accumulation at bottom and signs of oxidation on bus bar connections. Cleared contamination from panel interior, inspected all breaker connections, and verified proper circuit operation to restore full power to affected areas.