Plumbing & HVAC in Florissant, MO

Responded to service call for loud train-like noise coming from outdoor condensing unit during AC operation. Performed diagnostic inspection of residential split system with Goodman air handler. Identified issue with outdoor unit operation and documented system configuration including refrigerant line connections, ductwork assembly, and indoor equipment installation for repair recommendations.

Completed comprehensive heating maintenance and tune-up on residential furnace unit located in basement. Unit is under 10 years old and was found to be operating within manufacturer specifications. Performed standard preventive maintenance protocol including inspection of all major components, burner assembly, heat exchanger, blower motor, and safety controls. Replaced heavily soiled air filter which showed significant dust and debris accumulation that was restricting airflow. Verified thermostat operation and confirmed proper temperature control functionality at 70 degrees. All system components tested and confirmed operational, with unit ready for heating season demands.

Completed comprehensive super tune maintenance service on residential HVAC system with unit located at side of home and air handler in basement. Replaced heavily soiled air filter that showed significant dust and debris accumulation with new filter to restore proper airflow and system efficiency. Performed electrical diagnostics using multimeter to verify proper voltage and amperage readings across system components, ensuring all electrical parameters were within manufacturer specifications.

Completed comprehensive Supertune maintenance on Lennox furnace system located in basement mechanical room. Performed full system inspection, cleaned and serviced all components, checked condensate drain lines and PVC venting for proper operation, tested all safety controls, and verified optimal airflow through supply vents. System operating efficiently with all parameters within manufacturer specifications.

Completed comprehensive super tune maintenance service on two HVAC units, including one outdoor condensing unit located in the side yard and one Lennox furnace system in the basement. Performed thorough electrical diagnostics using digital multimeter to verify proper voltage and amperage readings across control boards and electrical components, inspected all refrigerant lines, ductwork connections, and wiring harnesses for both systems. All equipment tested within manufacturer specifications, with both units under 10 years old showing normal operating parameters and requiring no corrective actions at this time.

Completed comprehensive tune-up service on a 2-year-old HVAC system consisting of a Puron-based air conditioning unit (Model: DPVA412MCAA) and furnace. Performed full system inspection, replaced heavily soiled 16x25x1 air filter that showed significant dust and debris accumulation, verified refrigerant levels and pressures, inspected all manufacturer labels and safety documentation for compliance, and tested system operation to ensure optimal performance of both heating and cooling components.

Completed heating system tune-up on single unit located in basement. Performed comprehensive maintenance including filter inspection and replacement, thermostat functionality verification, and system diagnostics. Unit under 10 years old showed normal operating condition with Emerson programmable thermostat responding properly to temperature setpoint adjustments.

Completed comprehensive O10 furnace tune-up in basement location per Home Depot promotional service agreement. Performed full system inspection including blower motor assembly, gas valve, electrical connections, and internal components with access panel removed for thorough evaluation. Verified Honeywell Home thermostat operation showing proper heating mode function with setpoint at 71°F and current temperature reading of 75°F, confirming system cycling and fan auto operation as designed.

Completed comprehensive HVAC tune-up and maintenance on a 6-year-old air conditioning system and 11-year-old furnace, both operating properly at time of service. Performed diagnostic testing using clamp meter to verify electrical current readings on blower motor assembly (649 amp reading) and refrigerant line measurements (14.5 reading), inspected all mechanical components including heat exchanger, blower wheel, control board connections, and electrical wiring throughout the system. All components found to be functioning within normal parameters with no deficiencies noted.

Completed comprehensive tune-up and maintenance service on both furnace and air conditioning systems per Home Depot promotional offer. Performed full system inspection of both units, which were found to be operating properly with no reported issues. Inspected outdoor AC condenser coils, which showed significant accumulation of dirt, dust, and debris on fins, along with cobweb material present. Checked and replaced 20x25x1 pleated air filter to ensure proper airflow and system efficiency. Conducted standard maintenance procedures including visual inspection of all accessible components, verification of system operation, and assessment of overall equipment condition.

Responded to no-power call affecting multiple outlets throughout home and AC unit. Upon arrival, inspected main electrical panel and verified utility power had been restored after customer contacted power company. Tested affected circuits, confirmed proper breaker operation, and verified power restoration to all previously non-functioning outlets and AC unit throughout residence.

# HVAC Supertune Maintenance - Two Units Completed comprehensive supertune maintenance on two HVAC systems located at side of home and basement for Home Depot promotional service. Performed full system diagnostics including electrical amperage readings showing 6.11 amps on blower motor, inspected and documented air filter condition showing dust accumulation on pleated media with diamond-pattern mesh, verified all mechanical components, and ensured both units operating within manufacturer specifications.

Responded to kitchen sink clog caused by food debris, specifically raspberries that had entered the drain system. Upon arrival, accessed property through back entrance as front doorbell was inoperative. Inspected double-basin stainless steel sink with standing water in both basins. Opened cabinet access panel and examined plumbing configuration, which included a Badger 500 1/2 HP garbage disposal unit connected to standard PVC P-trap drainage system. Cleared blockage from disposal and drain line, restoring proper water flow and drainage function to both sink basins.

# O10 Furnace Tune-Up - Basement Installation Completed comprehensive tune-up service on a 10-year-old Lennox furnace located in basement. Upon inspection, unit exhibited significant dust accumulation, surface oxidation on metal components, and general wear consistent with age. Accessed interior compartment to inspect electrical connections, capacitor, and control wiring. All wire connections were verified secure with red, yellow, black, and blue wiring intact to respective terminals. Inspected capacitor and electrical components for proper operation. Noted heavy dust buildup throughout cabinet interior and on heat exchanger surfaces. Cleaned accessible areas to improve airflow efficiency and reduce potential fire hazards from debris accumulation. Examined ductwork connections showing standard wear and minor surface rust on galvanized metal transitions. Verified blower motor operation and checked amp draw within manufacturer specifications. Inspected gas valve assembly and confirme

Completed comprehensive supertune maintenance on two 15-year-old HVAC units. Performed full system inspection including thermostat operation verification (currently set at 72°F cooling mode with 71°F indoor temperature and 68% humidity reading), checked all electrical connections and wiring at gas valve assembly, inspected internal components including piping and condensate lines, and verified proper airflow and filter condition. Both systems operating within normal parameters upon completion.

Replaced a 5-foot section of deteriorated sewer line in basement floor per permit 26PLU-18570. Excavated through concrete basement flooring to access the heavily corroded pipe, which exhibited significant internal buildup and reduced diameter from rust and mineral deposits. Removed the failed section and installed new white PVC piping with proper fittings, backfilled the trench, and prepared the area for inspection.

Completed preventive maintenance tune-up on a residential cooling system over 10 years old located in backyard. Performed standard diagnostic testing including electrical measurements using digital multimeter, verifying system operating parameters and component functionality. Unit inspected and serviced according to manufacturer specifications with all safety checks completed satisfactorily.

Completed routine inspection and maintenance on a 10-year-old residential air conditioning unit located on the side of the house. Verified proper operation of all system components including electrical connections at the breaker panel, refrigerant lines, and condensate pump in the mechanical equipment area. Unit found to be functioning within normal parameters with no immediate repairs required at time of service.

Responded to a clogged shower drain in the basement bathroom. Upon inspection, discovered deteriorated flexible metal conduit and damaged piping components in the drain line assembly. Cleared the obstruction and documented the compromised conduit sections that will require future replacement to prevent recurring drainage issues.

Responded to service call for multiple electrical issues including non-functional kitchen sink light/switch, foyer lamp reinstallation, and aluminum wiring panel inspection. Troubleshot and repaired kitchen sink lighting circuit, identifying faulty switch connection. Reinstalled foyer light fixture with proper mounting and wiring connections as shown in ceiling junction box with multiple circuit wires. Conducted comprehensive inspection of main electrical panel containing aluminum wiring to assess proper terminations, connections, and overall safety condition. Verified all connections were properly torqued and treated with anti-oxidant compound per aluminum wiring standards. Documented meter installation and service entrance equipment condition. All circuits tested and confirmed operational upon completion.