24/7 HVAC & Plumbing Services in Red Bud, IL

Completed comprehensive Supertune maintenance on two HVAC units located in backyard and utility closet. Performed full system diagnostics, inspected and cleaned both units, verified thermostat operation showing proper heating function at 77°F, and replaced air filters on both systems which showed moderate dust accumulation. All equipment operating within normal parameters upon completion.

Responded to no cooling complaint on 9-year-old outdoor unit. Upon inspection, found blower motor operational but airflow restricted due to evaporator coil obstruction. Verified system specifications on Advanced Distributor Products evaporator coil model LC4260S1G. Cleaned coil, restored proper airflow, and confirmed adequate cooling delivery to occupied space.

Returned to diagnose cooling system that was previously found frozen. Performed thorough inspection of evaporator coil, refrigerant lines, and heat exchanger components. Documented interior condition of HVAC unit including refrigerant circuit, copper piping connections, and condenser coil assembly to determine root cause of freezing issue and inadequate cooling performance.

Responded to service call for condensation issues with AC system causing water accumulation in ceiling and vents. Upon inspection, found excessive sweating on both the indoor air handler and outdoor condensing unit. Diagnosed primary issue as blocked condensate drain line preventing proper drainage from the evaporator coil. Cleared obstruction from condensate drain system and verified proper flow through PVC drainage piping. Inspected Lennox furnace and air handler assembly for proper insulation and airflow restrictions. Checked refrigerant levels and confirmed system operating within manufacturer specifications. Verified all ductwork connections were secure and properly sealed to prevent future condensation issues. System tested and operating normally with no further water accumulation observed.

Completed comprehensive cooling system tune-up on Daikin air conditioning unit, performing standard maintenance checklist including inspection of indoor air handler electrical components, contactors, circuit breakers, and blower motor assembly. Exterior condenser unit inspected and serviced, with all system components found operating within normal parameters and customer presented with preventive maintenance agreement enrollment option.

Responded to no cooling condition on residential air conditioning system. Replaced defective control board and refrigerant sensor on evaporator coil, then installed surge protector to prevent future electrical damage. System tested and restored to normal cooling operation.

Replaced kitchen outlet serving refrigerator and installed new GFCI receptacle. Installed dual switch configuration to control newly added garbage disposal and light fixture. All electrical connections were made in accordance with NEC standards, devices were properly grounded, and functionality was verified upon completion.

Completed comprehensive cooling system tune-up on single AC unit, including inspection of electrical control board, wiring connections, and all major components. Verified proper operation of system controls, checked refrigerant levels, and inspected air filter condition within return air housing. All components found to be functioning within normal parameters with no immediate repairs required.

Completed comprehensive cooling system tune-up on outdoor condensing unit. Performed standard maintenance protocol including inspection of electrical components, refrigerant levels, condenser coil cleaning, and verification of proper system operation. Customer's preventive maintenance agreement was renewed onsite with auto-renewal activated per request.

Completed comprehensive cooling season tune-up on 7-year-old residential air conditioning system with outdoor condensing unit located in backyard and air handler in utility room. Performed full system inspection including electrical connections, refrigerant levels, condenser coil cleaning, blower assembly evaluation, and control circuit testing. All components found operating within manufacturer specifications; system cleared vegetation encroachment around outdoor unit to ensure proper airflow and documented equipment condition with photographic records.

Responded to no cooling call following suspected lightning strike. Upon arrival, found Lennox air handler operational but outdoor condensing unit completely non-functional with no power. Diagnosed electrical failure at condenser due to lightning damage. Inspected indoor air handler, refrigerant lines, and electrical connections—indoor equipment functioning properly with no visible damage to control board or wiring.

Completed comprehensive cooling system tune-up on 14-year-old ground-level air conditioning unit with air handler located in basement. Performed standard maintenance protocol including filter replacement, system inspection, and verification of proper operation. All electrical connections, ductwork, and condenser components were inspected and found to be in functional condition.

Completed preventive maintenance tune-up on a 20-year-old cooling system located in the basement. Performed comprehensive inspection of hydronic heating/cooling components including circulation pumps, flow indicators, pressure gauges, and associated piping connections. All system components found operating within normal parameters; documented equipment condition with photos for service records.

Returned to site to inspect electrical meter in coordination with Metro Electric. Documented existing outdoor electrical infrastructure including residential standby generator installation with associated gas supply line, shut-off valve, sediment trap, and conduit connections. Photographed generator unit mounted on concrete pad with proper ventilation and safety components, as well as exterior utility connections and piping configurations for service records.

Completed scheduled preventive maintenance on residential Generac standby generator unit. Performed comprehensive inspection of generator components, including visual assessment of electrical connections, conduit routing, and junction box installations. Inspected generator housing exterior condition, verified proper ventilation clearances, and documented equipment location relative to foundation and utility access points. All systems operating within normal parameters upon completion of maintenance service.

Responded to no heat call on under 10-year-old furnace located in hallway. Upon arrival, accessed unit and performed visual inspection of gas burner assembly, wiring harnesses, and internal components. Verified unit operation and confirmed furnace was heating properly at time of service visit, with all burners igniting correctly and system cycling normally to reach thermostat setpoint.

Responded to no cooling complaint on outdoor condenser unit located in backyard. Upon arrival, found 10+ year old system with visible weathering and oxidation on exterior casing. Performed diagnostic evaluation of unit surrounded by debris and fallen leaves, documented equipment condition with photographs showing aged components and refrigerant lines. Unit assessed for operational status and potential service needs related to reported cooling failure.

Replaced drain trap assembly on HVAC system and performed preventative maintenance safety check (PSCC). Verified thermostat operation showing proper temperature readings and inspected air filtration system with pleated filter in place. All components tested and confirmed operational for both heating and cooling modes.

Completed non-tuneup general heating maintenance on two furnace units located in basement mechanical closet. Performed standard inspection and operational testing on Lennox air handler systems. Verified thermostat functionality with Honeywell ProSeries unit displaying proper temperature readings at 65°F. All equipment operating within normal parameters with no issues identified requiring immediate attention.

Performed comprehensive heating tune-up on 9-year-old basement furnace, including inspection of electrical components, wiring connections, and control boards. Checked and verified proper operation of Emerson thermostat (currently reading 73°F) and confirmed system cycling. Filter was inspected and appears to be in good condition with minimal buildup.