Furnace, AC and Plumbing Services in Sappington, MO

Responded to complaint of loud whistling noise from basement damper when bedroom zone air conditioning was operating. Inspected 11-month-old HVAC system and ductwork in basement area. Assessed damper operation and airflow characteristics in affected zone to identify source of noise issue under warranty coverage.

Responded to service call for 13-year-old Goodman AC unit that would not stop running. Performed full diagnostic evaluation on ground-level exterior condenser unit and identified malfunction preventing proper cycling. Completed necessary repairs to restore normal thermostat control and operational cycling of the system.

Responded to service call for intermittent vibration noise from central air conditioning unit. Performed diagnostic inspection of outdoor condensing unit, which revealed dirt and debris accumulation on condenser coils visible through protective grille. Inspected mounting hardware, fan assembly, and compressor for loose components or mechanical issues that could cause vibration during operation.

Responded to service call for reported popping noise from one of two AC units upon startup. Arrived on-site and performed diagnostic inspection of Unit 10 located at side of property. Conducted visual examination of system components and documented condition of air handler return grille assembly. Inspected ventilation grille for proper mounting, structural integrity, and potential sources of mechanical noise during system cycling. Grille showed normal operational wear with minor dust accumulation on horizontal louvers. Evaluated ductwork connections, mounting hardware, and frame assembly for loose fasteners or contact points that could generate popping sounds during thermal expansion or compressor engagement. Photographed affected components for service documentation. System requires further evaluation of startup sequence and potential component repairs to resolve reported noise concern.

Completed comprehensive cooling system tune-up on 5-year-old ground-level AC unit. Performed refrigerant pressure and temperature diagnostics using manifold gauge set, confirming system operating within manufacturer specifications. Inspected indoor air handler components including blower motor assembly and verified proper electrical connections throughout system.

Performed camera inspection of sewer lateral line in response to basement flooding. Inspection revealed significant deterioration of pipe interior at approximately 42'10", including exposed substrate material and debris accumulation on pipe floor. Completed all required county paperwork on-site for sewer lateral program documentation and submission.

Responded to no cooling complaint on U10 outdoor unit located at side of home. Upon arrival, found unit shut off with condenser fan not operating. Connected manifold gauges and diagnostic equipment to assess system pressures and diagnose failure. Performed troubleshooting procedures to identify cause of cooling loss and fan motor failure.

Responded to no cooling complaint on Lennox residential AC system. Upon arrival, confirmed unit was blowing warm air. Performed diagnostic evaluation of system components including indoor air handler and outdoor condensing unit located in backyard. Inspected refrigerant lines, electrical connections, and verified proper airflow through system. Identified issue preventing proper cooling operation and presented repair options to restore system functionality.

Responded to no cooling complaint on 5-year-old Lennox system with excessive noise. Upon inspection, discovered severely deteriorated refrigerant line insulation and evidence of significant corrosion on copper piping throughout the evaporator coil assembly. Identified compromised suction line insulation allowing heat gain and reducing system efficiency. Replaced degraded foam insulation on refrigerant lines, cleaned oxidized copper connections, and verified proper refrigerant flow. System tested post-repair with normal operating temperatures and noise levels restored. Unit returned to full cooling capacity with whole-home comfort achieved.

Responded to service call for garage ceiling fan with no airflow. Inspected large industrial-style ceiling fan and verified motor operation. Determined fan was functioning properly but rotating in reverse direction, pulling air upward instead of circulating downward. Reversed fan direction using directional switch to correct airflow pattern and confirmed proper air circulation throughout garage space. Provided quote for installation of two exterior GFCI-protected outlets per customer request.

Completed comprehensive air conditioning tune-up on 13-year-old residential cooling system equipped with White-Rodgers thermostat. Performed full preventive maintenance protocol including inspection of all major components, verification of thermostat operation displaying 72 degrees, assessment of furnace and ductwork configuration, and system performance evaluation to ensure optimal readiness for upcoming cooling season.

Responded to a clogged drain call at a 70-year-old residential property. Upon inspection, located heavily corroded cast iron drain stack in basement with significant rust deterioration throughout the vertical piping system. Accessed cleanout port on main drain line and cleared obstruction using mechanical augering equipment. Inspected exterior drain access point beneath deck structure, removing accumulated debris and vegetation that had infiltrated the system. Successfully restored proper drainage flow and confirmed clearance with water test.

Completed comprehensive cooling system tune-up on ground-level outdoor unit. Performed standard maintenance including inspection of control board wiring and connections, cleaned condenser coil and filter screen which showed accumulation of outdoor debris, verified all electrical components and safety controls operational. System tested and operating within normal parameters.

Completed comprehensive cooling maintenance tune-up on a 15-year-old residential air conditioning system. Performed full system inspection including electrical components, capacitor testing, control board evaluation, and verification of proper operation. System found to be functioning properly with all components operating within normal parameters at time of service.

Returned to diagnose frozen evaporator coil on recently installed system. Utilized digital manifold gauges to assess refrigerant pressures and temperatures, verifying system operating parameters. Unit was non-operational due to freeze-up condition at time of arrival.

Responded to no cooling call and diagnosed failed contactor in outdoor condensing unit. Replaced defective contactor with new component, restoring proper operation to system. Unit tested and confirmed cooling normally upon departure.

Returned to service call to complete repair on air handler unit. Replaced control board, RDS (reversing drain sensor), and installed coil sensor repair kit to restore proper system operation. All replacement parts were obtained from Lennox Bridgeton and original components were retained per protocol. Verified system functionality and confirmed proper temperature readings at floor register upon completion.

Responded to service call for newly installed HVAC system with blower motor continuously running despite thermostat set to auto mode. Inspected air handler unit, documented refrigerant line connections, electrical disconnect components, and internal equipment configuration. Photographed system components including refrigerant lines, mounting hardware, reflective duct insulation, and condensate drain pan for diagnostic purposes and service records.

Completed comprehensive tune-up service on two residential air conditioning units, both approximately 5 years old with one ground-mounted unit and one basement-mounted unit. Performed standard preventive maintenance procedures including inspection of blower assemblies, capacitors, electrical connections, and refrigerant lines on both systems. All components were found to be in good operating condition with no immediate repairs required.

Responded to service call to verify proper operation of electrical outlets in garage. Upon inspection, identified faulty outlet requiring replacement. Removed existing outlet from wall box, disconnected wiring, installed new outlet with proper wire connections using appropriate wire nuts and connectors, and restored outlet to full functionality. All outlets tested and confirmed operating properly upon completion.