Professional Edwardsville, IL HVAC & Plumbing Contractor

Completed comprehensive tune-up service on two 10-year-old furnace units located in basement. Performed full system inspection including electrical connections, terminal integrity, capacitor testing, and blower assembly evaluation on both units. Verified thermostat operation and temperature calibration, confirming proper communication between control system and heating equipment.

Responded to service call for system requiring refrigerant charge. Upon arrival, connected manifold gauge set to measure system pressures and confirmed low refrigerant levels in R22 system. Added refrigerant to manufacturer specifications and verified proper system operation upon completion.

Completed comprehensive tune-up and maintenance service on a single outdoor cooling unit located in side yard. Performed standard inspection of all major components including compressor, condenser coils, electrical connections, and refrigerant levels. Noted significant age-related deterioration with heavy rust formation on internal components and substantial dust accumulation throughout the system, indicating extended service life without recent maintenance. Observed that outside disconnect box shows signs of weathering and may require replacement in the near future to ensure safe operation and proper electrical disconnection capability.

Completed comprehensive furnace tune-up service on single basement unit for Home Depot program. Performed electrical diagnostics and system testing using digital multimeter to verify proper voltage, amperage, and system performance. All measurements confirmed equipment operating within manufacturer specifications.

Completed preventive maintenance tune-up on two cooling systems, both over 10 years old, with one unit located in the side yard and the other in the basement. Performed standard inspection of condenser coils, verified proper airflow through grilles, and assessed overall system operation on both units to ensure optimal performance for the cooling season.

Replaced evaporator coil on second-floor HVAC system and removed one of two existing filter driers to bring system to proper configuration. All defective components were disposed of, and system was returned to proper operation.

Performed diagnostic evaluation on 15-year-old Trane air conditioning system to address reported cooling concerns and mismatched indoor/outdoor equipment configuration. Inspected air handler unit model RCFL-HM3621CC (manufactured 05/20/2010) and assessed filtration setup, confirming customer's concern regarding dual filter arrangement inconsistent with outdoor condensing unit specifications. Documented equipment nameplate data, measured air handler dimensions, and photographed existing installation to evaluate compatibility issues between interior and exterior components. Provided technical assessment of current system configuration and discussed options for bringing indoor air handler into proper alignment with outdoor unit to restore optimal system performance without requiring complete system replacement.

Responded to service call for non-functioning LED light fixture in kitchen. Upon arrival, assessed the fixture and determined it required complete replacement due to failed internal components. Removed existing defective LED fixture, verified electrical connections and circuit integrity at the electrical panel, and installed new LED light fixture. Tested operation to confirm proper functionality and restored lighting to the kitchen area.

Conducted on-site assessment for new electrical panel installation at residential property. Documented existing exterior electrical infrastructure, including current meter base mounted on white vinyl siding with white PVC conduit system. Evaluated service entrance configuration and accessibility for panel upgrade work. Vegetation around foundation and service entrance area noted for clearance considerations during installation phase.

Returned to complete electrical installation for kitchen range hood as part of ongoing HVAC and lighting project. Completed wiring and power connection for stainless steel chimney-style range hood unit, ensuring proper electrical supply to ventilation system, LED lighting, and control panel. Verified all electrical connections were secure and hood controls functioning properly, including multi-speed fan settings and integrated lighting features. Installation completed successfully with unit fully operational.

Performed comprehensive second-opinion diagnostic on 2-year-old residential air conditioning system. Conducted thorough inspection of outdoor condensing unit including visual examination of condenser coils, electrical connections, capacitor, and compressor motor assembly. Utilized digital multimeter to test electrical components and verify proper voltage and capacitance readings. Inspected wire connections with twist-on connectors for secure termination and proper polarity. Evaluated condenser coil condition, finding fins clean and free of debris or damage. Assessed compressor motor mounting and electrical connections for integrity. Verified disconnect box and electrical service connections at exterior wall. Provided detailed findings and discussed maintenance membership options with homeowner, noting family member's existing relationship with company.

Completed comprehensive cooling season tune-up on basement AC unit, including inspection of air handler, evaporator coil, electrical connections, and control board. Verified proper airflow through pleated filter media, tested all safety controls and circuit functionality, and documented system condition with photos showing clean wiring terminations and operational components. All systems operating within manufacturer specifications with no immediate service needs identified.

Responded to no cooling call on 15-year-old AC system with outdoor unit not running and thermostat displaying "waiting on equipment" message. Upon arrival, performed electrical diagnostics using digital multimeter to test voltage and continuity at outdoor unit's control panel. Identified failed dual run capacitor with reading of 35.05 microfarads, significantly below manufacturer specifications, preventing compressor and condenser fan motor from starting. Replaced defective capacitor with properly rated OEM replacement part, verified all electrical connections, and tested system operation. Unit successfully started with compressor and outdoor fan running at correct amperage, thermostat communication restored, and system cooling normally. Advised customer that 15-year-old system is nearing end of expected service life and recommended consideration of replacement options for improved efficiency and reliability.

Completed comprehensive tune-up service on a 10-year-old residential air conditioning unit located on the side of the home. Performed standard maintenance inspection of the air handler cabinet, verifying electrical connections, circuit breaker operation, and proper wiring configuration throughout the system. Inspected and documented a moderately soiled air filter showing significant dirt accumulation in the lower pleated sections, indicating normal system operation and particle capture over the service period.

Responded to no-cool complaint on U10 unit experiencing repeated freeze-up conditions since installation. Upon inspection, found severely restricted airflow due to dirty air filter at indoor air handler. Replaced filter with proper specification unit and verified adequate airflow across evaporator coil. Advised proper filter maintenance schedule to prevent future freeze-up occurrences.

Coordinated with HVAC contractor on initial site visit to assess and plan completion of range hood installation project. Documented existing ceiling configuration with drop ceiling tiles, recessed lighting, and wall finishes to determine final electrical connection requirements for kitchen exhaust system.

Completed electrical fixture installation in residential interior space. Work included proper mounting, wiring connections, and testing of new lighting fixture to ensure safe operation and code compliance. Minor drywall patching was performed at installation point to achieve clean finished appearance.

Responded to service call for non-operational HVAC system following previous technician's misdiagnosis that resulted in damaged control board. Replaced faulty control board with new unit sourced from supply house, restored system functionality, and performed diagnostic testing to verify proper operation. Discarded damaged board per protocol as warranty claim was not applicable due to technician error during prior service visit.

Responded to no-cooling callback on 10+ year old AC unit that had been shut off. Upon inspection, found evaporator coil with significant dirt accumulation and heavily corroded copper refrigerant lines showing orange-brown oxidation. Observed moisture and condensation patterns inside air handler indicating previous operational issues. Documented coil condition showing yellowish-brown discoloration on aluminum fins and rust-colored deterioration on copper tubing connections. System components showed signs of age-related wear and potential refrigerant circuit compromise due to copper line corrosion.

Responded to no cooling complaint on 10+ year old Lennox unit located in backyard. Upon arrival, confirmed clogged condensate drain line preventing proper system operation. Cleared drain line obstruction, verified proper drainage flow, and tested system operation. Unit cooling properly at departure with thermostat displaying appropriate temperature differential.