HVAC and Plumbing Services in Maplewood, MO

Responded to service call for clogged drains affecting both kitchen and bathroom sinks. Upon arrival, performed diagnostic assessment to determine the nature and location of the blockage within the drainage system. Inspected accessible plumbing infrastructure in the basement utility area, including exposed PVC drain lines and waste piping visible along the walls and ceiling joists. Cleared obstructions from affected drain lines using appropriate drain cleaning equipment and techniques. Verified proper drainage flow was restored to both the kitchen and bathroom sink fixtures. Tested drainage performance to ensure complete resolution of the clogging issue and confirmed all fixtures were draining properly at the conclusion of service.

Completed installation of 40-gallon short gas water heater in basement utility area. Installed new copper supply piping with hot and cold shut-off valves, 3/4" pressure reducing valve, and blue thermal expansion tank mounted to ceiling joists. All connections properly soldered and secured per code requirements. Plumbing permit #26PLU-16101 obtained and ID sticker applied to installation. System tested for proper operation and checked for leaks. Unit staged and ready for customer use.

Responded to no cooling call on residential system over 10 years old located in side yard. Upon arrival, found outdoor condensing unit not operating and homeowner had been advised to turn system off. Performed diagnostic evaluation of HVAC system including electrical components, contactor, capacitor, and thermostat communication. Inspected indoor air handler and noted multiple air filters stored in basement area. Tested system operation and identified failure point preventing unit from engaging. Completed necessary repairs to restore cooling function and verified proper system startup and operation before departure.

Responded to no cooling complaint on residential HVAC system over 10 years old. Upon inspection, found evaporator coil completely frozen with heavy ice buildup on refrigerant lines and coil surface, preventing proper airflow and heat exchange. Coil fins showed significant dust accumulation and debris restriction. Observed rust and corrosion on exterior metal components and framework indicating age-related deterioration. System was shut down per prior instruction to allow ice to thaw and prevent compressor damage from continued operation in frozen condition.

Responded to no cooling call with reported water leak on 5-year-old upstairs air handler system. Upon arrival, unit had been shut off per prior instructions. Inspected air handler installation in upstairs closet, documented equipment condition and drain line routing. Advised customer of findings and recommended next steps for system evaluation and leak source identification.

Completed comprehensive air conditioning tune-up and maintenance on a 2-year-old outdoor condensing unit. Performed full system inspection including refrigerant pressure check, electrical connections testing, capacitor evaluation, and condenser coil cleaning. Replaced dirty air filter at indoor air handler, verified proper airflow through return air plenum, and confirmed all ductwork connections were secure. System operating within manufacturer specifications with no deficiencies noted.

Responded to no-cool call at property being prepared for sale. Upon arrival, inspected outdoor condensing unit and found failed dual-run capacitor preventing compressor and condenser fan operation. Replaced defective capacitor with proper rated replacement, restored power, and verified system startup with normal amperage draws on both compressor and fan motor. Unit cooling properly at time of departure.

Completed installation of a 50-gallon STERLING electric tall water heater in basement utility area. Unit installed with proper copper piping connections, blue expansion tank mounted above, and all connections secured to code. Permit #26PLU-14749 applied with required plumbing identification sticker affixed to unit for inspection compliance.

Responded to service call for high electric bill concern potentially related to air conditioning system. Performed comprehensive system diagnostics using refrigerant manifold and micron gauge on single condensing unit located in side yard. Measured and recorded refrigerant pressures, superheat, subcool, and system temperatures to evaluate overall performance and efficiency of the unit, which is less than 10 years old.

Responded to water leak complaint on 15-year-old residential split AC system. Upon arrival, inspected indoor air handler unit located in utility closet and outdoor Distinction brand condenser unit. Identified source of water leak at indoor unit. Cleared condensate drain line obstruction and verified proper drainage flow. Inspected evaporator coil drain pan for cracks or damage, confirmed integrity. Checked refrigerant lines and insulation for condensation issues. Tested system operation and confirmed no further leaking. Documented equipment condition with photographs of both indoor and outdoor units for service records.

Responded to service call for furnace leaking water from top of unit in basement. Inspected condensate drainage system, cleared blockage in drain line, and verified proper water flow. System tested and operating normally with no further leakage observed.

Completed comprehensive air conditioning tune-up on single outdoor unit located at ground level on side of home. Performed standard maintenance protocol including system inspection, filter evaluation, and equipment assessment of furnace and HVAC components in basement mechanical room. All equipment photographed and documented, with air filter showing clean condition and proper wire grid support structure intact, and furnace unit with connected ductwork and PVC venting operating within normal parameters.

Performed comprehensive maintenance and repair on dual mini-split system. Installed new safety switch to ensure proper unit operation and protection. Completed thorough Jet Pack cleaning service on both indoor air handler units, including blower wheel and internal components to restore optimal airflow and system efficiency.

Responded to no cooling complaint on residential Lennox furnace system (Unit 10). Upon arrival, performed diagnostic inspection of HVAC equipment and replaced dirty 16x25x1 Aerostar pleated air filter that was restricting airflow. System tested and confirmed operational with proper cooling restored.

Responded to service call for ductless mini-split system not cooling bedroom and displaying 2-blink error code indicating indoor coil thermostat error. Upon arrival, accessed indoor air handler by opening front cover to inspect evaporator coil assembly and internal components. Diagnosed thermostat sensor malfunction affecting communication between indoor unit and temperature control system, preventing proper cooling operation.

Responded to report of air conditioning system not cooling properly overnight with Nest thermostat not blowing cold air. Upon arrival, system was operational and cooling effectively to setpoint of 75°F. Performed diagnostic inspection of indoor air handler, examining blower wheel assembly for potential airflow restrictions or mechanical issues. Verified proper system operation, confirmed adequate airflow through blower assembly, and documented thermostat functioning correctly in cooling mode at time of service.

Performed level one maintenance service on HVAC system, including thorough blower wheel cleaning and evaporator coil cleaning. Removed blower wheel assembly from unit for detailed cleaning to restore proper airflow and system efficiency. Cleaned evaporator coil to remove accumulated dirt and debris, improving heat transfer and overall system performance.

Responded to service call for 22-year-old Amana air conditioning system with reported noise coming from outdoor condensing unit during operation. Performed diagnostic testing on the condenser unit using clamp meter to measure electrical amperage draw, recording 186.8 amps during testing sequence. Connected manifold gauges with refrigerant hoses to system to evaluate operating pressures and assess compressor performance. Inspected condenser coils, fan motor operation, and electrical connections on outdoor unit to identify source of abnormal noise and determine necessary repairs for proper system function.

Performed comprehensive cooling system tune-up on a 3-year-old residential air conditioning unit. Completed full system inspection including refrigerant levels, electrical connections, condenser and evaporator coil cleaning, air filter replacement, thermostat calibration, and condensate drain line verification. All components found operating within manufacturer specifications with no deficiencies noted; system returned to optimal performance.

Completed preventative maintenance tune-up on a 15+ year old air conditioning unit located in basement utility area. Performed standard system inspection, replaced air filter, and verified proper operation of all components. Unit tested and left in good working order.