Ductwork Services in Olivette, MO

Performed camera inspection of south roof drain line. Accessed drain system through interior storage closet area where plumbing infrastructure is located. Documented drain line conditions and interior access point with photographic evidence for further evaluation and recommendations.

Completed scheduled HVAC maintenance on commercial cooling system serving restroom facility. Inspected air distribution components, ceiling-mounted ventilation equipment, and thermostat controls to ensure proper operation and temperature regulation throughout the space.

Completed scheduled heating maintenance tune-up on HVAC system serving second floor zone. Inspected wall-mounted digital touchscreen thermostat control panel, confirmed proper operation and menu functionality. Accessed air handling unit, removed and inspected air filter which showed significant dust accumulation with visible debris pattern across lower section; replaced filter with new unit to restore proper airflow and system efficiency. Verified heating system operational status, all components functioning within normal parameters at time of service completion.

Responded to no cooling call on 8-year-old Trane system with non-operational outdoor fan. Diagnosed failed dual run capacitor preventing condenser fan motor operation. Replaced defective Genteq capacitor with properly rated replacement, restored system to full cooling operation, and verified all electrical connections at contactor were secure.

Responded to no cooling complaint on second floor 15-year-old Lennox system. Upon arrival, confirmed outdoor condenser unit running but indoor air handler not producing cool air. Connected manifold gauge set to service ports and performed refrigerant pressure analysis. System pressures indicated significant refrigerant undercharge. Conducted thorough leak inspection of both indoor evaporator coil and outdoor condenser coil. Inspected all refrigerant line connections, service valves, and accessible copper line sets for signs of refrigerant loss. Evaluated overall system condition noting age of equipment and wear patterns consistent with original installation. Documented findings with photos of outdoor unit with gauges attached and indoor air handler installation. Discussed system performance issues and repair options with customer. Due to age of equipment and extent of required repairs, customer elected to defer decision until Tuesday. Left system in safe condition with all service port

Successfully installed a 50-gallon tall gas water heater (A.O. Smith ProMax model) in basement location. Installation included proper venting configuration with metallic ductwork, connection of hot and cold water supply lines using copper and appropriate piping materials, and installation of safety shutoff valves with green handles. All plumbing connections were completed to code specifications, gas line properly connected, and temperature/pressure relief valve installed. Work performed under plumbing permit 26PLU-17333 with licensed plumber supervision. Unit tested for proper operation, all connections inspected for leaks, and installation verified to meet manufacturer specifications and local building codes.

Completed comprehensive cooling maintenance on a 9-year-old Lennox AC system with SL280UH110V060-D5 furnace. Performed standard tune-up procedures including inspection of blower assembly, verification of manufacturer specifications, and system operational testing. Unit confirmed operating properly with all components functioning within normal parameters.

Completed time and materials piping installation work for fountain system. Reviewed technical documentation including vault installation specifications and lifting procedures with Series 2/2H vault pad sections. Installation performed according to manufacturer guidelines with proper equipment and safety protocols for underground vault positioning.

Responded to reported sewer backup affecting first-floor toilet and washing machine drain. Upon inspection, identified clogged main drain line causing wastewater to back up through the plumbing stack into the laundry area. The toilet on the second floor was leaking from the stack connection, indicating pressure buildup in the system due to the blockage. Performed diagnostic assessment of the drainage system to locate the obstruction point. Cleared the main sewer line blockage using professional drain cleaning equipment, restoring proper flow and eliminating the backup condition. Verified that wastewater was draining correctly from both the toilet and washing machine discharge line. Inspected the stack connection at the second-floor toilet for any damage from the leak and confirmed proper sealing after clearing the blockage. Tested all affected fixtures to ensure complete resolution of the drainage issue and proper system function. Advised on preventative maintenance recommendations

Conducted plumbing site inspection and documented existing conditions. Photographed deteriorated wall-mounted access panel showing significant rust damage, paint failure, and structural compromise with exposed cavity at damaged edge. Documented PVC pipe connection and mounting hardware condition. Also photographed floor-level pipe stub or drain opening protruding from concrete surface, along with visible floor impressions indicating previous fixture or equipment placement. Images captured for assessment of required repairs to damaged access panel and evaluation of rough-in plumbing conditions.

Responded to no cooling complaint on residential split system over 10 years old located at side of home. Upon arrival, confirmed air handler was running in fan-only mode as previously instructed to prevent potential compressor damage. Performed diagnostic evaluation of outdoor condensing unit and indoor air handler components. Inspected Lennox furnace/air handler assembly in basement mechanical room, verifying proper airflow, electrical connections, and refrigerant line integrity. Assessed condenser unit operation, checking capacitor function, contactor operation, and compressor start-up sequence. System restored to normal cooling operation following diagnostic procedures and minor adjustments. Verified proper temperature split across evaporator coil and confirmed adequate airflow delivery. Unit cycling properly with thermostat calling for cooling.

Completed comprehensive cooling system tune-up on single ground-level outdoor AC unit. Performed full system inspection including evaluation of condenser coil condition, blower motor assembly, and electrical connections. Condenser coils showed moderate debris accumulation and leaf buildup requiring attention for optimal heat transfer efficiency. All components found operational with system ready for continued service.

Installed new condensate drain line for Bryant HVAC system. Ran new drainage piping to properly route condensate away from the furnace unit, resolving drainage issues. System tested and verified operational upon completion.

Installed dedicated electrical outlet for ice cream machine at gas station location. Ran new circuit from main electrical panel using flexible metal conduit, installed weatherproof outlet boxes on exterior wall, and terminated connections to accommodate equipment power requirements.

Completed first annual cooling system maintenance on Lennox unit installed last summer. Performed comprehensive AC tune-up including inspection of all major components, replaced air filter showing accumulated dust and debris, verified proper airflow through condenser grille, and confirmed system operational status. All maintenance items completed per manufacturer specifications with unit operating within normal parameters.

Responded to clogged drain issue in basement laundry area. Upon arrival, found standing water on floor with visible water damage and staining throughout tiled surface. Cleared obstruction from floor drain using appropriate drain cleaning equipment, restoring proper water flow and drainage function. Verified drain was operating correctly and water was evacuating properly through the system.

Responded to service call for Mitsubishi mini split system in room above garage blowing warm air. Upon arrival, performed diagnostic evaluation of outdoor condensing unit and indoor air handler. Inspected refrigerant line set, electrical connections, and condensate drainage system. Unit was originally installed by unknown contractor. Documented equipment condition with photos showing outdoor unit placement against exterior wall with line set routing and electrical disconnect panel. Identified issues preventing proper cooling operation and provided repair recommendations to restore system functionality.

Replaced three zone dampers in the HVAC system to restore proper zoning functionality. Installed new Honeywell ZoneFast motorized damper actuators with modulating controls and manual override capability. Successfully tested system operation in both heating and cooling modes to verify proper damper response and zone control.

Responded to no cooling complaint on 2-year-old Lennox unit. Upon inspection, found failed dual run capacitor in air handler control section. Capacitor tested at zero microfarads, preventing compressor and condenser fan motor operation. Replaced defective SUREPHON capacitor with OEM-equivalent component matching proper voltage and microfarad specifications. Verified all electrical connections secure, tested system operation, and confirmed unit cooling properly with normal amperage draws on both compressor and fan motor circuits.

Replaced defective evaporator coil in attic unit under warranty (S/N 6018C39085). Recovered refrigerant, removed failed coil, installed new Lennox evaporator coil, evacuated system using vacuum pump, recharged to manufacturer specifications, and verified proper system operation with manifold gauges showing acceptable temperatures and pressures. Unit restored to full heating and cooling functionality, defective coil disposed of per warranty protocol.