Professional Belleville, IL HVAC & Plumbing Contractor

Completed heating tune-up on a 2-year-old furnace located in the utility closet. Performed comprehensive system inspection including blower motor examination, electrical connections check, burner assembly evaluation, and heat exchanger inspection with lower access panel removed for thorough component access. Verified thermostat operation, tested all safety controls, and confirmed proper airflow through ductwork system.

Completed preventive maintenance tune-up on basement furnace unit per Home Depot service agreement. Performed comprehensive system inspection including thermostat operation verification, burner assembly examination, gas valve functionality check, and internal component assessment. All systems tested and confirmed operational with no deficiencies noted.

Installed new electrical outlet in cabinet above oven to accommodate microwave installation. Ran circuit from main electrical panel to cabinet location, ensuring proper wire gauge and circuit protection for appliance load requirements. No complications encountered during installation.

Responded to service call for commercial electrical outlet assessment. Upon arrival, performed comprehensive evaluation of exterior electrical outlets requiring replacement. Inspected dual-outlet configuration including standard duplex receptacle and GFCI outlet mounted on exterior wall with weathered trim board. Conducted electrical testing using portable GFCI circuit tester to verify ground fault protection functionality and circuit integrity. Evaluated electrical meter panel installation containing dual digital utility meters with associated conduit and protective enclosures. Documented existing conditions through photographic evidence showing outlet configuration, protective devices, and meter infrastructure. Provided estimate for outlet replacement work addressing weathering concerns and ensuring code-compliant GFCI protection for exterior receptacles.

Completed comprehensive tune-up and maintenance on single air conditioning unit located in side yard. Performed standard preventive maintenance procedures including inspection of dual-run capacitor (60/5µF) and electrical connections, verification of proper wire terminations and contactor operation, and assessment of overall system components. Inspected associated basement furnace and ductwork infrastructure. Upon initial service notes indicating small leak concern, conducted thorough examination of refrigerant lines and connections; documented system condition with photos of electrical panel components and mechanical room layout for service records.

Completed comprehensive tune-up service on basement furnace unit as part of Home Depot promotional maintenance program. Performed full system inspection including blower motor assembly, gas valve operation, control board functionality, and all electrical connections. Verified proper operation of all safety controls, cleaned accessible components, and documented system condition with interior compartment photography showing blower assembly, circuit board, and wiring harnesses in satisfactory working order.

Responded to service call for non-functioning stairwell light fixture with suspected wire damage from recent AC installation. Upon arrival, accessed electrical panel to inspect circuit breakers and verify power distribution to affected fixture circuit. Photographed panel configuration showing dual columns of circuit breakers with directory labels for documentation purposes. Traced circuit serving stairwell lighting and confirmed panel integrity with all breakers properly seated and functional. Investigation revealed wiring issue consistent with customer's concern regarding recent HVAC work potentially compromising electrical connections. Restored power to stairwell fixture and verified proper operation upon completion.

Completed comprehensive heating system tune-up on single residential HVAC unit as scheduled through Home Depot service program. Performed full system inspection including thermostat functionality verification, internal component examination of furnace assembly including draft inducer motor, heat exchanger, burner assembly, gas valves, and control board with all electrical connections. All components found operating within normal parameters and system confirmed ready for heating season operation.

Responded to service call for outdoor condensing unit experiencing loud banging noise, vibration, and intermittent shutdown under first-year warranty coverage. Upon inspection, discovered significant debris accumulation in condenser coil fins and surrounding components, which can cause airflow restriction, increased operating pressures, and potential compressor cycling issues. Documented unit condition with photographs showing heavy dirt buildup on exterior panels and within finned coil assembly, along with gravel and debris lodged between components that could contribute to operational noise and vibration concerns reported by customer.

Responded to service call for circuit breaker that would not remain in the on position for two-bedroom circuit. Upon arrival, conducted visual inspection of exterior electrical service equipment including meter enclosure and main panel accessibility. Verified power supply integrity at meter base and confirmed proper utility connection. Documented existing electrical infrastructure with digital photographs showing Ameren Gridstream RF digital meter installation, service entrance equipment, and exterior panel configuration mounted on residential vinyl siding. Based on symptom description of breaker failing to lock in position, issue indicates internal breaker mechanism failure requiring breaker replacement to restore reliable power to affected bedroom circuits.

Completed comprehensive tune-up service on a basement-installed furnace unit as part of a Home Depot maintenance program. Performed standard preventative maintenance procedures including inspection of all accessible components, ductwork assessment, and system evaluation to ensure proper operation for the upcoming heating season. Unit showed normal wear consistent with age, with all major components functioning within acceptable parameters at time of service.

Responded to no-cool call with EE internal fault error message displayed on thermostat and unit continuously running without cycling off. Performed diagnostic inspection of basement ground-level unit, examining blower motor assembly, capacitor, wiring connections, and control board components. Advised customer to shut off air conditioning system and operate thermostat in fan-only mode to prevent further damage until internal fault can be properly diagnosed and repaired.

Performed comprehensive electrical safety inspection of residential property. Conducted thermal imaging scan of all accessible outlets and wall surfaces to identify potential hotspots or abnormal heat signatures—no elevated temperatures detected. Inspected main electrical panel and documented existing conditions: noted moderate corrosion and rust on panel frame edges where metal meets wall surface, indicating possible moisture exposure over time. Verified all circuit breakers for proper seating and operation; all breakers functional with no signs of overheating or damage. Evaluated wire management within panel box—connections secure though wire bundling shows typical age-related congestion. Tested smoke detector for proper operation and battery condition. Inspected visible outlets throughout property for secure mounting, proper grounding, and signs of arcing or heat damage—all outlets tested within normal parameters. Overall electrical system operating safely with no immediate hazards

Installed new electrical subpanel in attic space to support third-floor heating system expansion. Ran conduit and wiring from main service panel through crawl space, mounted subpanel to ceiling joists, installed circuit breakers, and completed all connections per code requirements.

Responded to no cooling call at residential property. Upon arrival, found heavily soiled air filter restricting airflow to system, causing loss of cooling capacity. Replaced dirty filter with new unit, restored proper airflow, and verified system operation with adequate cooling throughout home.

Completed comprehensive tune-up service on single furnace unit located in basement. Performed standard maintenance protocol including inspection of blower assembly, heat exchanger, and electrical components; verified proper operation of ignition system and safety controls; replaced air filter with new Flanders filter; and cleaned accumulated dust and debris from equipment housing and surrounding area.

# HVAC Service - No Cool 10+ Responded to service call for outdoor unit making unusual noises during shutdown cycle on 10+ year old system. Upon arrival, performed comprehensive system inspection including indoor air handler and outdoor condensing unit. Inspected blower assembly and filter housing, noting accumulated dust and debris on blower wheel and housing surfaces. Checked indoor air handler components for proper operation and airflow restrictions. Evaluated outdoor unit for mechanical issues related to reported shutdown noise. Documented system conditions with photos showing blower assembly with visible dirt accumulation on squirrel-cage fan and filter housing, as well as overall basement installation configuration with ductwork connections. System evaluated for age-related wear and proper operation of all major components.

Completed comprehensive tune-up and maintenance on residential air conditioning system found in proper working order. Performed standard preventative maintenance procedures including inspection of indoor air handler unit, ductwork, and outdoor condenser unit. Outdoor unit coils showed accumulation of dirt and debris which were addressed during service, ensuring optimal heat transfer and system efficiency for continued reliable operation.

Completed comprehensive Supertune maintenance service on a 10-year-old split system with furnace located in basement and AC unit in backyard. Performed full system inspection, cleaned and serviced all accessible components including blower assembly, draft inducer motor, and electrical connections. Verified proper operation of both heating and cooling systems, documented equipment condition with interior component photography showing normal wear consistent with age, and ensured all safety controls and wiring connections were secure and functioning properly.

Completed preventive maintenance tune-up on single residential air conditioning unit located at rear of property. Removed significant accumulation of leaves, twigs, and organic debris from exterior condenser unit that had collected around perimeter and top edges. Inspected and serviced indoor air handler component, including air filter assessment. Unit returned to proper operating condition following standard tune-up protocol per Home Depot maintenance program specifications.